Mother’s Day is right around the corner. Let your mom know what an awesome mom she is with a handwritten message. Choose from 2 watercolor floral Mother’s Day card designs. Simply download, print, cut, and fold to create your own 4″x6″ card.
I am so excited to share the latest update to our home. I have been wanting to update the door trims ever since we moved in. The existing door trims are outdated and are missing an inch off the bottom because the house used to have carpet. Since we are going to add new baseboards throughout the house soon, this would be the time to get in new door trims. I went with craftsman style door frames because I like the simple and clean look it gives off.
The hardest part was getting all the necessary tools for this project. I made over 5 runs to Lowe’s to get everything I needed. I had to purchase a finishing nail gun and an air pressure tank for this project. Learning how to use both of those was scary. After getting over my fear of learning how to use a new power tool, the project was actually pretty simple. 🙂
Take a look at the transformation and the steps I took to get to our lovely new craftsman style door trims. I ended up updating the door hinges and door knobs once the trim was finished. Made a big difference!
Sources I looked at before beginning this project:
Poplar Wood [Measure your door and decide length of wood you need to buy]
What I used for standard door:
Finishing Nail Gun
2″ Finishing Nails
Air Pressure Tank
NPT Couple/Plug Kit (if you need a converter in order to attach the air pressure tube to the tank and nail gun)
White Paint (I bought the Valspar Ultra White. They sell this pre-made at Lowe’s)
Clamps (recommended but may not be necessary)
Cut along both edges of the trim to remove the caulk. This makes sure that you do not peel paint off the wall when removing the trim.
Use a flat head screwdriver (or chisel) and a hammer to remove the casing/trim. I tried both and preferred using a flathead screwdriver over the chisel.
Use the backside of the hammer to pull off the existing door trim and to remove nails that are still stuck in the door frame.
Sand down the door frame to make sure you have a flat surface for the new trim. This makes sure that the new trim will sit flush against the wall, with as little of a gap as possible.
Measure and cut the wood to match the door frame.
Measurements for the door to my home office.
1×4 at 81″ in length (cut 2 of these)
1×4 at 38″ in length
1×2 at 39″ in length
0.25×2 at 39″ in length
You can sand down the surface of the wood if it is not smooth.
Build the top of the door trim by glueing the 1x4x38, 1x2x39, 0.25x2x39 pieces together. If the wood is a little bent when you are trying to glue the pieces together, you will need to use a clamp to make sure there is good contact between the three pieces. There should not be any gap between the pieces. You can also you a nail gun to nail the pieces in place. I prefer using the clamps so there is less to touch up.
Use wood filler putty to cover up the nail holes. And sand down the surface when it is dry.
Caulk the edges of the door trim.
Place painter’s tape around the frame to protect your walls and put some paper on the floor to protect your floors.
Brush on the paint a little at a time to prevent drips and uneven coating. I used roughly 4 coats of paint.
After I finished the first door, I needed to do the 2 other doors next to it. It looked weird having only one door frame updated. Here’s some pictures of the final result with updated hinges and door knobs. I am super happy with the way they turned out. Will need to paint the doors and update the wall color. 🙂
A friend of ours was moving and gave us a door mirror from Target. It has just been sitting in our garage collecting dust for 5 months or so. I came across this DIY mirror tutorial on Shanty 2 Chic on how to reframe a cheap mirror yourself. I’ve been looking for a mirror for our entryway and thought this would be a great opportunity to upcycle the door mirror and hang it up in the entryway.
I followed the tutorial from Shanty 2 Chic and added a few extra steps like sanding down the surface and applying a mirror hanger, since I wanted to hang it up. The Shanty 2 Chic tutorial also said it would only take 1 hour but it ended taking up half a day for me. I waited 1 hour before adding two coats of polyurethane to the stained wood frame.
Here is how to upcycle a cheap door/wall mirror.
1×4 white wood boards (I purchased three 1x4x48″ wood boards from Lowe’s)
X-acto or utility knife
Picture Hanging System
1) Remove the paper on the back of the mirror.
2) Use a blade to slice through the glue holding the mirror to the frame. I used an exacto blade, but you can also use a utility knife. Make sure you cut along the edge of the frame and cut through the glue.
3) Pull the frame away from the mirror without bending the mirror. Remove the mirror carefully so that it does not break.
4) Spray and clean the mirror surface with Windex.
5) Cut 45 degree angles at each end of one of the wood boards to build the frame. I used a miter saw to make the 45 degree angle cuts.
Lay the first piece you cut on top of the second 48″ wood board and use a pencil to trace the 45 degree angle edges on both sides of piece 2.
This makes sure you have 2 identical 48″ long wood boards.
Measure out 17 1/4″ on the third wood board and cut. Trace and cut the fourth piece.
You should end up with:
2 @ 48″ (long point to long point)
2 @ 17 1/4″ (long point to long point)
6) Layout the pieces over the mirror to make sure the size of the frame is correct.
7) Use wood glue to join the ends of the pieces together to make the frame. And staple the backside of the frame to make sure the frame stays in place while drying. I put heavy paint cans on top of the corners to ensure they stayed in place. Use clamps if you have them.
8) Use a power sander to sand down all surfaces to prepare the wood before you stain it. Sand down the edges of the frame by hand, so they aren’t sharp. I used #100 sand paper for the edges. Note: the Rust-Oleum wood stain can provides instructions on how to sand and prep the surface before staining.
9) Stain the frame with one coat of wood stain and add polyurethane to protect the wood.
Follow the can for instructions. I used Rust-Oleum Carrington wood stain and polyurethane.
10) Lay the mirror in place on the backside of the frame and use a pencil to trace the edges of the mirror. **Make sure you leave enough room for the picture hanging system above the mirror.** Remove the mirror and spread out the liquid nails inside the pencil marks. I used a wooden coffee stirrer to spread out the liquid nail. Lay the mirror face down onto the back of the frame. Line it up with the pencil marks.
11) Measure and drill holes into the backside of the frame and the wall where the mirror will be hanging. Use a level when figuring out where the holes should be on the wall. Screw Picture Hanging System in place.
12) That’s it! Hang out your new mirror and enjoy! 🙂
I have been needing a place to jot down important events and our shopping list. That is the reason for this simple DIY dry erase wall calendar. This DIY wall calendar is super easy to make, and does not require a printer. It is easily customizable to your style and space and is perfect for your command center at home or office wall.
Card stock paper
Scissors (or X-acto blade)
Glass photo frame
Step 1: Choose a glass photo frame. I wanted one that would give me enough space to write down events for the calendar, so I purchased a 18″x24″ frame.
Step 2: Purchase fabric that is slightly bigger than the frame to make sure that the fabric fits seamlessly in the frame.
Step 3: Place fabric inside the frame and fold over the over flowing fabric to match the edges of the glass. Pin down the fabric that is folded over.
Step 4: Iron the fabric to get rid of wrinkles and to flatten down the parts that were folded over.
Step 5: Measure and cut card stock paper to size to fit your frame. These were my measurements.
Calendar date boxes- 2.5″ x 2″
Day of the week the boxes – 2.5″ x 0.75″
Large notes box – 6.5″ x 8.5″
Small notes box – 6.5″ x 3.75″
Step 6: Layout the boxes on the fabric and place double sided tape on each square. Flip over the boxes and secure in place with the double sided tape.
Step 7: Flip the fabric over so that the side with the boxes are against the glass, and put on the frame backing.
Step 8: Fill in the month, days, and type of notes you want for each note box.
All done! 🙂 Now all you need to do is hang it up.
Learn how to personalize a mug with a Sharpie Oil-Based Paint Marker and a white porcelain mug. It is super simple and a fun creative activity for groups or yourself! It can be used for so much more than just another coffee mug.
Some ideas include:
1) Succulent pots for home decor
2) Pen holder
3) Bridal shower or party activity station
4) Party favors
1) Purchase white porcelain mugs. I bought the FÄRGRIK Mug from Ikea for $0.99 each.
2) Clean the mugs. Use Lysol wipes to clean the surface you are drawing on, or just wash the entire cup with dishwashing liquid.
3) Choose an oil-based marker to draw with. I used the Sharpie oil-based paint markers. They have various color options and come in different thicknesses – extra fine, fine, and medium point.
4) Personalize your mug. Choose a pattern, quote, mustache, animal… the possibilities are endless.
5) Bake in your design onto the mug. Place your mug(s) on a baking sheet and insert onto the middle rack in the oven. Set the oven to 350°F for 30 minutes. Make sure you turn on the oven AFTER the mugs have been placed in the oven. Leave the mugs in the oven to cool to prevent cracks.
6) Handling & Care: Make sure you hand wash the mugs. Using the dishwasher will mess up your design. My sister put hers in the dishwasher and the beautiful gold color changed to an ugly orange. YIKES!